+44 (0)1985 850 954

sales@robertpearson.co.uk

Water Flow Regulators

  • Up to 70% Water Savings at Taps, Showers etc
  • Helps comply with The Code For Sustainable Homes
  • Can help you achieve BREEAM Wat 1 credits

Application

Point of use regulators designed to provide constant and maximum flow rates at outlets such as taps and showers etc., irrespective of changes in demand or water pressure fluctuations between 1 Bar - 10 Bar (unless otherwise stated below).

Benefits

  • Large water savings and also by reducing the amount of hot used you can achieve large energy savings
  • Even water distribution throughout the site, even at peak demand periods
  • Lower capital costs (potential savings from smaller pipework, water heating systems etc.)
  • Reduced "peak demand"
  • Ideal for retro-fit or new build projects
  • Low cost solution. Payback often within months
  • Help reduce "back splash" at basins

RP/ACC model Combined Isolating Valve and Flow Regulator (c/w: access port)

Application: Outlets supplied with water pressure 0.5 Bar - 6 Bar maximum.

Order Codes:

15mm RP/ACC
22mm RP/ACC

With access port on side of valve to allow removal of flow regulator cartridge (and optional strainer) without draining down system or breaking pipework (picture: above), for the purpose of flushing out the system on commissioning or changing the flow regulator cartridge to a higher or lower flow rate as required.

Available in 15mm or 22mm sizes and comes with colour coded cap to show the flow rate the valve is set to. Flow rates and colour coding for both sizes are:

2.5 Lpm Lime Green
4 Lpm Pink
6 Lpm Grey
8 Lpm White
10 Lpm Yellow
12 Lpm Brown
15 Lpm Blue
18 Lpm Green

Optional strainer available upon request. Red and/or blue handles for the valves available on request.

RP/ISO model Combined Isolating Valve and Flow Regulator

Order Code: 15mm RP/ISO

15mm combined flow regulating & isolating valve with integral flow regulator. Optional handle available on request.

Flow rates from any of 4, 5, 6, 8, 10, 12 or 15 Lpm.

4 Lpm Grey
5 Lpm Yellow
6 Lpm Black
8 Lpm White
10 Lpm Blue
12 Lpm Red
15 Lpm Green

RP/GA Flow Regulator Insert for your own compression ended valves

 

Order Codes:

15mm RP/GA

Circular flow regulator insert (only) for your own valves. Simply fit in to the tap/appliance side of your own compression ended valve.

Flow rates for 15mm 4, 6, 8, 10, 12, 15 and 18 Lpm.

4 Lpm Pink
6 Lpm Grey
8 Lpm White
10 Lpm Yellow
12 Lpm Brown
15 Lpm Blue
18 Lpm Green 

 

Combined Aerator & Flow Regulator

Order Code: RP/CAAFR

Aerators add air into the water as it leaves the tap in order to help reduce splashing when water hits the basin.

No plumbing required to fit. Simply replace existing tap aerator with this unit.

Flow rates/colour-coding as follows:

1.9 Lpm Lime Green
3.8 Lpm Blue
5 Lpm Orange
6 Lpm Black
8 Lpm White

Combined laminar (unaerated flow straightener) and flow regulators are also available. Please call to discuss if required.

½" Shower Flow Regulator

Order Code: RP/SFR/DW

Ideally fit this unit at the thermostatic mixing valve end of the flexi-hose. If fixed head shower, unscrew the showerhead, screw the flow regulator in and then re-fit the shower head. No plumbing required to it.

Flow rates/colour-coding as follows:

4 Lpm Grey
6 Lpm Black
8 Lpm White
9 Lpm Orange
10 Lpm Blue
12 Lpm Red
15 Lpm Lime Green

½" MxF Chrome Tap Tail/Mixer & Flow Regulator

Order Code: RP/DWSA/TTFR

Simply screw on to ½" inlet pipe thread to an appliance.

Flow rates/colour-coding as follows:

1.4 Lpm Brown
1.9 Lpm Yellow
2.5 Lpm Orange
3.5 Lpm Beige
5 Lpm Violet
6 Lpm Pink
7 Lpm Green
8 Lpm Red
9 Lpm Lilac
10 Lpm Black
12 Lpm White