+44 (0)1985 850 954

sales@robertpearson.co.uk

Programmable Sensors

Sensor Taps

The Panel Mounted Programmable Sensor is available in brushed stainless steel. You will need to purchase a hand held programmer to adjust the settings yourself on site.

Universal sensor can be used to control your own tap spouts, urinals, showers, WCs … just specify the kit you want from the options below.

Programmable Panel Mounted Tap Sensor (to control your own tap spout)

Adjustable settings include; run-on time, sensor range, wave-on/wave-off operation, automatic purge to help prevent water dead legs, anti-vandal features and more including a “lock-out” setting to help prevent excessive operations in a specified period.

Simply put your hand within the sensing range to activate the water. As long as the sensor detects your hand water will continue to run. Take your hand away and the water will stop after the pre-set but adjustable overrun time.

Sensor Taps

Tap Sensor Kit Order Codes:

PsensT-B
Battery powered tap sensor kit
Kit c/w:1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

PsensT-M
Mains powered tap sensor kit
Kit c/w:1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve ,1 x Pre-wired 6V PSU

For applications that require separate hot and cold supplies per basin please use special colour coded sensors

Battery Powered Kits

Blue Insert (Cold) Tap Sensor Kit Order Codes:

PsensT(B)-B
Battery powered tap sensor kit
Kit c/w: 1 x Programmable Sensor (with blue indicator), 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

Red Insert (Hot) Tap Sensor Kit Order Codes:

PsensT(R)-B
Battery powered tap sensor kit
Kit c/w: 1 x Programmable Sensor (with red indicator), 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

Mains Powered 2 Tap Kit

Red + Blue Inserts 2 Tap Sensor Kit Order Code:

PsensT(R+B)-M / 2 Tap Kit
Mains powered tap sensor kit
Kit c/w: 2 x Programmable Sensors (1 red, 1 blue), 2 x Pre-wired 15mm Solenoid Valves, 1 x Pre-wired 6V PSU, 1 x T-Connector

Technical Data:

  • Cut-out hole Panel mounted (Ø28mm drill hole required).
  • Sensing Range Programmable from settings 1 – 10.
  • Overrun time This is the time the water will continue to flow after you take your hands away from the sensor. Programmable from: 2, 5, 10, 15, 20 & 30 seconds.
  • Wave-on/Wave-off Normally OFF. When switched ON this allows you to override the standard overrun time by putting your hand in front of the sensor for a second time (if you don’t, the water will still turn off after the pre-set but adjustable overrun time).
  • Anti-vandal time This is automatic water turn-off time in case someone puts e.g. chewing gum over the sensor to try and keep the tap running constantly. Programmable from: 30 secs, 1, 2, 4 & 8 minutes.
  • Automatic purge When purge is programmed ON, if a tap has not been used for a certain period of time it will automatically turn itself on to purge itself to help prevent water dead legs. Tap non use times before purge is activated from any of: 3, 6, 12, 24, 36 & 48 hours. Programmable water on time per purge from: 30 seconds, 1, 2, 4, & 8 minutes.
  • Lock-out Normally OFF. When set ON this allows the system to lock out if tap sensor has been activated from any of 4, 6, 8 & 10 operations in a single 15 minute period. The lock out period is 15 minutes and the system will automatically re-set itself once the lock out period has elapsed.

Programmable Panel Mounted Individual Urinal Sensor

Adjustable settings include; pre-flush wait, pre-flush time and main flush time, sensor range and automatic purge to help prevent water dead legs.

Sensor Taps

Urinal Sensor Kit Order Codes:

PsensU-B
Battery powered urinal sensor kit
Kit c/w:1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

PsensU-M
Mains powered urinal sensor kit Kit c/w:1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired 6V PSU

*STANDARD CABLE IS 800MM. IF USING DC PIPE INTERRUPTERS YOU MAY NEED TO SPECIFY OPTIONAL 2000MM CABLE. PLEASE CALL TO DISCUSS

Technical Data:

  • Cut-out Hole Panel mounted (Ø28mm drill hole required).
  • Sensing Range Default 5. Adjustable 1 – 10.
  • Pre-Flush Wait Default 1 second. Adjustable between 1 – 2 seconds.
  • Pre-Flush Time Default OFF. Adjustable 1 – 3 seconds. When set to ON, this allows a “pre-flush” which is a short flush as the person arrives at the bowl.
  • Main Flush Wait 10 seconds. NOT adjustable. Person must be constantly detected for at least 10 seconds before the system will allow a main flush to occur when the person walks away again from the urinal.
  • Main Flush Time Default 2 seconds. Adjustable from 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 7.5, 8, 8.5, 9, 9.5 & 10 seconds. The main flush occurs within a few seconds of the person finishing and walking away from the urinal bowl.
  • Automatic Purge Default OFF. When set to ON the system will create a Purge Flush if the Urinal has not been used for your choice of 6, 12, 24, 36, 48 or 72 hours.
  • Purge Run Times Default 4 seconds. Adjustable 2, 4, 6, 8 or 10 seconds. This is the length of time the valve will open for on each Purge flush.

Programmable Panel Mounted Shower Sensor (to control your own shower)

Adjustable settings include; run-on time, sensor range, wave-on/wave-off, automatic purge, anti-vandal, lock-out and more.

Sensor Taps

Shower Sensor Kit Order Codes:

PsensS-B
Battery powered shower sensor kit
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

PsensS-M
Mains powered shower sensor kit
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired 6V PSU

Technical Data:

  • Cut-out hole Panel mounted (Ø28mm drill hole required).
  • Sensing range Programmable from settings 1 – 3.
  • Run time Default setting 1 minute. Programmable from: 30 seconds, 1, 2, 3, 4 and 5 minutes.
  • Wave-on/Wave-off Normally OFF. If switched ON this allows you to turn the shower off, and immediately override the Run Time, by simply putting your hand within the detection zone of the sensor for a second time. (The shower will still turn itself after the Run Time if you do not).
  • Anti-vandal time Run Time + 10 seconds. This is automatic water turn-off time in case someone puts e.g. chewing gum over the sensor to try and keep the shower head running constantly.
  • Automatic purge When purge is programmed ON, if a shower has not been used for a certain period of time it will automatically turn itself on to purge itself to help prevent water dead legs. Shower non-use times before purge is activated from any of: 3, 6, 12, 24, 36 & 48 hours. Programmable water on time per purge from: 30 seconds, 1, 2, 4, & 8 minutes.
  • Lock-out Normally OFF. When set ON this allows the system to lock out if a shower sensor has been activated for more than any of 4, 6, 8 & 10 operations in a single 15 minute period. The lock-out period is 15 minutes and the system will automatically re-set itself once the lock-out period has elapsed.

Programmable Panel Mounted Bath Sensor (to control your own bath spout)

Adjustable settings include; run-on time, sensor range, wave-on/wave-off, automatic purge, anti-vandal, lock-out and more.

Sensor Taps

Bath Sensor Kit Order Codes:

PsensB-B
Battery powered bath sensor kit
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

PsensB-M
Mains powered bath sensor kit
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired 6V PSU

For applications that require separate hot and cold taps per bath please use special colour coded sensors

Battery Powered Kits

Blue Insert (Cold) Bath Tap Sensor Kit Order Codes:

PsensB(B)-B
Battery powered bath sensor (blue) kit
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

Red Insert (Hot) Bath Tap Sensor Kit Order Codes:

PsensB(R)-B
Battery powered bath sensor (red) kit
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired 15mm Solenoid Valve, 1 x Pre-wired Battery Pack

Mains Powered 2 Tap Kit

Red + Blue Inserts Bath 2 Tap Sensor Kit Order Code:

PsensB(R+B)-M / 2 Tap Kit
Mains powered bath sensor (red + blue) kit
Kit c/w: 2 x Programmable Sensors, 2 x Pre-wired 15mm Solenoid Valves, 1 x Pre-wired 6V PSU, 1 x T-Connector

Technical Data:

  • Cut-out hole Panel mounted (Ø28mm drill hole required).
  • Sensing Range Programmable from settings 1 – 3.
  • Run time Programmable from: 1, 2, 3, 4, 8 & 10 minutes.
  • Wave-on/Wave-off Normally OFF. When switched ON this allows you to override the standard overrun time
  • by putting your hand in front of the sensor for a second time (if you don’t, the water will still turn off after the pre-set but adjustable overrun time).
  • Anti-vandal time RUN + 10 seconds. This is automatic water turn-off time in case someone puts e.g. chewing gum over the sensor to try and keep the tap running constantly.
  • Automatic purge When purge is programmed ON, if a tap has not been used for a certain period of time it will automatically turn itself on to purge itself to help prevent water dead legs. Tap non use times before purge is activated from any of: 6, 12, 24, 36, 48 & 72 hours. Programmable water on time per purge from: 30 seconds, 1, 2, 4, & 8 minutes.
  • Lock-out Normally OFF. When set ON this allows the system to lock out if tap sensor has been activated from any of 2, 4, 6 & 8 operations in a single 15 minute period. The lock out period is 15 minutes and the system will automatically re-set itself once the lock out period has elapsed.

Programmable "Auto" WC Sensor

Fit sensor directly behind where a person sits on the WC. When that person finishes and walks away the WC will automatically flush.

Auto Flush Valve

Adjustable settings include; sensor range, detect times, flush times and walk away times, automatic purge, lock-out and more.

Sensor Taps

Order Codes:

PsensWC-AUTO-B
Battery powered
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired WC Flushvalve, 1 x Control Box and Battery Pack

PsensWC-AUTO-M
Mains powered
Kit c/w: 1 x Programmable Sensor, 1 x Pre-wired WC Flushvalve, 1 x Control Box and 6v PSU

Technical Data:

  • Cut-out hole Panel mounted (Ø28mm drill hole required).
  • Sensing range Default 5. Adjustable 1 – 10.
  • User Detect Time Default 5 seconds. Adjustable between 1 – 10 seconds. This is the time the sensor needs to constantly detect a person for before going on to a flush mode.
  • Dual Detect Time Default 20 seconds. Adjustable 10, 12, 14, 16, 18, 20, 22, 24, 26 & 28 seconds. If a person finishes and leaves the sensing area before the end of this time, the system will only provide a half flush.
  • Flush Times Default 4 seconds. Adjustable 2, 2.5, 3, 3.5, 4, 3/4.5, 3/5, 3.5/5.5, 4/6 & 6.5 seconds. This is the length of time the valve will open for on each flush. Where it states (eg) 3/5, this means 3 Lpm (“Half” flush) / 5 Lpm (“Full” flush). 
  • Walk Away Time Default 2 seconds. Adjustable 1, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5 & 5.5 seconds. This is the delay time after the sensor has stopped detecting some before the system will activate the flush.
  • Automatic Purge Default OFF. When set to ON the system will create a Purge Flush if the WC has not been used for your choice of 3, 6, 12, 24, 36, 48 or 72 hours.
  • Purge Run Times Default 4 seconds. Adjustable 2, 3, 3.5, 4, 4.5, 5, 5.5, 6 & 6.5 seconds. This is the length of time the valve will open for on each Purge flush. 
  • Lock Outs Default OFF. When set to ON the system will Lock-Out for 15 minutes if more than 2 -10 operations (adjustable) have occurred in a single 15 minute period. The Lock-Out will automatically re-set itself at the end of the 15 minute period.